The 6th International Conference on Compressor and Refrigeration (ICCR) is a series of conference, originating from the International Compressor Technique Conference (ICTC), which started in 1993. This conference becomes an important academic conference in the field of compressor and refrigeration, offering attendees an opportunity to discuss the current technique, information and products. Its field includes positive displacement and centrifugal compressors for refrigerants, air, and other gases, together with their system analysis, modeling, control and operation.

PART 1 COMPERSSORS

 1. Geometry of Screw Compressor Rotors and Their Tools.

 2. Application of Digital-Scroll Compressor on Reefer Container.

 3. Performance Analysis on a New Thermo-Chemical Compressor.

 4. Cold Cylinder Compression Cycle for Rotor Type Compressor.

 5. Analysis on Energy Savings of Refrigerating Compressors in Design and Operation.

 6. Realization of Stepless Capacity Regulation for Reciprocating Compressor.

 7. Numerical Study on the Oil Pump System of Rotary Compressor.

 8. Study on High Performance Inlet and Discharge Valves of Linear Compressor.

 9. Application and Design of the Metal Bellow Sealing In the Scroll Machinery.

 10. A New Type of CNG Refueling System and Equipment.

 11. Different Factors Influence on Acoustic Performance and Frequency

for Refrigeration Compressor's Shell.

 12. The Advanced Programming of Software Used For Design of Screw Rotor Profile.

 13. The Study of Heat Pump Water Heater with Vopour Injection Scroll Compressor.

 14. An Investigation of Flow Leakage in Water Hydraulic Vane Pump.

 15. Sealing Issue through the Gap between Vane Tip and Cylinder Wall in the Rotary Vane Expander.

 16. State of the Art Design and Calculation of Vessels and Piping Systems in Reciprocating Compressors.

 17. Assessment of Simulation Models for Heat Transfer in Suction Mufflers of Reciprocating Compressors.

 18. Numerical Analysis of Resistive Torques during the Start up of a Reciprocating Compressor.

 19. An Integrated Numerical - Experimental Project: The "Variable Capacity Compressor" Case.

 20. Investigation of Sliding Wear Resistance on Hermetic Compressor.

 21. A Study on the Wear Characteristics of a Journal Bearing According To

Its Material in the Scroll Compressors.

 22. Lubrication Characteristics of Nano-Oil at the Journal Bearing Of Scroll Compressors.

 23. Effects of Nano-Lubricants on the Friction and Wear Characteristics at

Thrust Slide-Bearing of Scroll Compressors.

 24. Comparison of Tribological Characteristics of Carbon-Based Nano Lubricants.

 25. Optimizing a Rolling Piston Compressor Using a Genetic Algorithm.

 26. 3D Force Measurements of Households Compressors.

 27. Compressor Shell Vibration Estimation Using Sound Field Measurements from Microphone Arrays.

 28. Noise Reduction in Screw Compressors by the Control of Rotor Transmission Error.

 29. A Dynamic Model of a Scroll Compressor.

 30. The FEM Analysis of a Real Compressor Housing.

 31. Development of a Twin Screw CO2 Compressor for NH3/CO2 Cascade Refrigeration System.

 32. Development and Performance Measurement of a Reciprocating Transcritical CO2 Compressor.

 33. Influence on Friction Coefficient of Grey Cast Iron According to the Variable

Viscosities of the Mineral Lubricant.

 34. Advances in numerical and experimental investigation of screw compressors.

PART 2 REFRIGERATION AND OTHERS

 35. The Experimental Study on the Effect of Evaporator Configuration on Frosting

Characteristic of Air Source Heat Pump.

 36. Study on Performance of Cool Storage Tank with Rectangular Capsules for Refrigeration System.

 37. Experimental Study on Two-Stage Compression Low Temperature Air Source Heat Pump Water Heater.

 38. Analysis and Improvement of Oil Return Method for HFC-134a Screw

Chiller in Transitional Season.

 39. Thermodynamic Analysis on Heat Pump with Gas Refrigerant Elicitation.

 40. Influence of Stability of Carbon Black Nano-Particle Suspension of Ammonia Solution.

 41. Research for the Characteristics of the Binary Ice Vacuum Preparation.

 42. Feasibility Study On HCFC22 Alternative Refrigerant: Propane (R290)

And Its Solubility with Lubrication Oils.

 43. Experimental Research and Analysis on Absorption Enhancement of Ammonia solution By AL203 Nan fluid.

 44. Experimental Research on Influence of Air Inlet Modes on CO2 Hydrate Formation Using Water Spraying.

 45. Substitution of Hydrate Guest Materials for Cool Storage.

 46. The Applied Prospect of Ground Source Heat Pump in China.

 47. An Investigation of the Once-Through Falling-Film Performance of

Libr Absorption Refrigeration System.

 48. The Influence of Working Fluids and Regenerator Parameters on Performance

of the Stirling-Cycle Refrigerator.

 49. Experimental Study on the Performance of a High Temperature Heat Pump

Using R134a as the Refrigerant.

 50. Experimental Study Of Humidity Measurement And Humidity Field Based On Environmental Chamber.

 51. Influence of the Leakage of Natural Non-Azeotropic Mixture Refrigerant

R600a/CO2 on System Performance of Auto'Cascade Refrigeration Cycle.

 52. Simulation of Gas Engine-Driven Heat Pump (GEHP) In Cooling Mode.

 53. Low Simulation of Air Refrigeration System Using Cold Air Distribution in Train.

 54. Development of Pelton-Type Expander Used In Refrigeration System.

 55. Energy Recovery on the Expansion Process Using a Turbo Expander at HFC134a Chiller.

 56. Performance Evaluation of Nano-Lubricants at Refrigeration Oil.

 57. performance Evaluation Of A Refrigerator Equipped With Liquid-Suction Heat

Exchangers Under The Influence Of Non-Condensable Gases.

 58. Two-Phase Flow Heat Transfer during R-410A Vaporization in Horizontal Small Tubes.

 59. Economic Analysis of GHP and EHP System for University Facilities in Korea.

 60. Lubrication Characteristics of Nano Lubricant Containing Fullerene Nanoparticles.

 61. Effect of Oil Mixing On the Pool Nucleate Boiling Heat Transfer Coefficient of Natural Refrigerant CO2.

 62. Design and Analysis of Multiple Parallel-Pass Condensers.